 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TD62S310AFM TOSHIBA Bipolar Digital Integrated Circuit Silicon Monolithic TD62S310AFM 1-Channel Darlington Source-Current Driver The TD62S310AFM is a 1-channel noninverting source-current driver. The driver incorporates an input resistor which limits output pull-down resistance and base current. The driver is optimal for driving fluorescent display tubes and LEDs. When using the driver, pay attention to the thermal conditions. Features * * * * * Ultra-small HSON6 package with heat sink on rear Large output voltage: VOUT = -50 V (min) Large output current: IOUT = -100 mA (max) Built-in input resistor: RIN = 10 k Input signal: High Level Active Weight: 0.017 g (typ.) Pin Connection (top view) Basic Circuit Diagram 20 k9 VCC OUTPUT 1 6 INPUT INPUT 10 kW 2.6 k9 10 k9 TEST VCC 2 5 P-GND 3 4 NC Rpd TEST OUTPUT P-GND Note 1: Diodes shown using dotted lines are parasitic. Do not use them. Note 2: When using the driver, connect the OUTPUT pin to the TEST pin. Note 3: When using the driver, connect the P-GND pin to the heat sink on the rear of the package. 1 2001-12-05 TD62S310AFM Maximum Ratings (Ta = 25C) Characteristics Supply voltage Output voltage Collector-emitter voltage Output current Input voltage Power dissipation Symbol VCC VOUT VCEO IOUT VIN PD (Note 4) Rth (j-a) (Note 4) Saturated thermal resistance Rth (j-c) (Note 5) Operating temperature Storage temperature Topr Tstg 25 -40~85 -55~150 C C Rating -0.5~50 -50 50 -100 -0.5~15 0.78 160 C/W Unit V V V mA V W Note 4: 114.3 76.2 1.6 mm glass epoxy film substrate Note 5: When an infinite heat sink is mounted. Cu heat dissipation pattern 100 mm 2 Recommended Operating Condition (Ta = -40~85C) Characteristics Supply voltage Output current Input voltage Output ON Input voltage Output OFF Symbol VCC IOUT VIN VIN (ON) VIN (OFF) Test Condition 3/4 Ta = 60C, Tj = 105C 3/4 3/4 3/4 Min 3/4 3/4 3/4 2.0 0 Typ. 3/4 3/4 3/4 5.0 3/4 Max 50 -100 12 12 V 0.8 Unit V mA V Electrical Characteristics (Ta = 25C) Characteristics Output leakage current Output saturation voltage Symbol ICEX VCE (sat) Test Circuit 1 2 Test Condition VIN = 0.4 V VIN = 2.0 V, IOUT = -70 mA VIN = 2.0 V, IOUT = -50 mA VIN = 3.6 V VIN = 12 V VCE = 2.0 V, IOUT = -70 mA IOUT = -500 mA VIN = 5 V, VCC = 50 V 3/4 RL = 625 W, CL = 15 pF Min 3/4 3/4 3/4 3/4 3/4 3/4 0.5 3/4 168 3/4 3/4 Typ. 3/4 3/4 3/4 240 1.1 3/4 3/4 3/4 240 0.2 2.0 Max 10 1.3 V 1.1 350 1.6 2.0 3/4 0.8 312 3/4 3/4 V mA kW ms mA mA Unit mA Input current IIN (ON) VIN (ON) VIN (OFF) 3 Input voltage Power dissipation Output pulldown resistor Turn-on delay Turn-off delay 4 3 3/4 5 ICC (ON) Rpd tON tOFF 2 2001-12-05 TD62S310AFM Test Circuit 1. ICEX VCC 2. VCE (sat) VCC VCE (sat) VIN ICEX IOUT VIN 3. IIN (ON), ICC VCC IIN (ON) VIN ICC 4. VIN (ON), VIN (OFF) VCC VCE VIN (ON) VIN (OFF) IOUT 5. tON, tOFF tr INPUT VCC INPUT 10% RL CL (Note 7) tON 90% 90% 50% 50% 50 ms 10% tOFF 90% 0 VOH tf 5V Pulse generator (Note 6) Note 6: Pulse width 50 ms, Duty cycle 10% Output impedance 50 W, tr < 5 ns, tf < 10 ns = = Note 7: CL includes probe and jig capacitance. OUTPUT 10% VOL Caution on Application 1. The device does not include protectors such as an overcurrent protector and an overvoltage protector. Applying excessive current or voltage may damage the device. Thus, design with great care to prevent excessive current or voltage from being applied to the device. The device may also be damaged by short-circuits between outputs and power supply/ground. Take care when designing output, VCC and GND line. 2. If the TD62S310AFM is used to drive an inductive load (such as a motor, solenoid, or relay), Toshiba recommends that the diodes be connected between pin 1 and pin 5 so as to absorb the counter electromotive force generated by the load. Please adhere to the maximum ratings of this device. 3. Be sure to mount the device in the correct orientation. Make sure that the positive and negative power supply pins are connected the right way round. Otherwise, the absolute maximum current and power dissipation ratings may be exceeded and the device may break down or undergo performance degradation, causing it to catch fire or explode, and resulting in injury. 3 2001-12-05 TD62S310AFM Package Dimensions Weight: 0.017 g (typ.) 4 2001-12-05 TD62S310AFM Preliminary land pattern 1.6 0.7 0.25 1.6 1.3 0.7 0.6 2.2 0.6 Unit : mm 10 mm Preliminary PCB trace dimension 0.7 5 mm 5 2001-12-05 TD62S310AFM RESTRICTIONS ON PRODUCT USE 000707EBA * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The products described in this document are subject to the foreign exchange and foreign trade laws. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. * The information contained herein is subject to change without notice. 6 2001-12-05 |
Price & Availability of TD62S310AFM
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |